Book Today!

 

The content down below on the subject of How to Install a Bathtub Yourself is indeed compelling. Give it a try and draw your own final thoughts.

Installing a bathtub isn't exactly rocket science, however it does need solid plumbing, woodworking, and also occasionally, tiling skills. Changing an old bathtub with a new one is additionally a reasonably difficult task. If the old bathtub is easily accessible, the project can move easily; if you need to open up a wall surface to remove the old tub and also position the new bathtub, the job is a lot harder. In either situation, the project is within a residence handyman's skills, although you will certainly require a helper to vacate the old tub and also set in the brand-new one. Make sure you have actually qualified on your own for the task and are comfortable trying it. Rather than employing a professional to take control of a halfway-completed task, it is better to think about utilizing one before you begin. Opportunities are you may require a professional plumber to make tube links.
This post will certainly help you install a brand-new tub in your restroom if you have actually currently bought a new tub and also don't need to transform the setup of your previous water supply pipelines.
Your tools and also product checklist need to make up the following:

 

• New Bathtub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Knife


• Measuring tape


• Pipe Caps


 

Planning for the Setup

Firstly, the supporting structure supplied with the bathroom should be fitted (if needed) according to the manufacturer's guidelines. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is essential to make certain that if the faucet comes with a plastic washer, it is fitted in between the bath and the faucets. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the taps system to prevent pressure on the bath tub.
Fit the adaptable faucet connectors to the bottom of the two taps utilizing 2 nuts and olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet with the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Ensure you use all of the supplied washers.
Attach the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom need to now be ready to be suited its final setting.

 

 

Removing Old Touches

If you require to replace old taps with brand-new ones as a part of your installment, then the first thing you need to do is separate the water supply. After doing so, switch on the faucets to drain pipes any kind of water staying in the system. The process of eliminating the existing faucets can be fairly troublesome because of the restricted access that is frequently the case.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the faucets. Have a fabric all set for the remaining water that will certainly originate from the pipelines. Once the supply pipes have actually been eliminated, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from transforming during this procedure. As soon as the faucets have been removed, the holes in the bath/basin will have to be cleaned of any old sealing compound.
Prior to proceeding to fit the brand-new faucets, contrast the pipeline links on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the new taps to fit.

 

 

Setting up the Bath tub

Making use of both wood boards under its feet, put the tub in the required setting. The wood boards are practical in evenly spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto 4 small factors.
The next objective is to make sure that the bath tub is leveled all round. This can be attained by inspecting the level and also readjusting the feet on the tub up until the spirit level checks out level.
To install taps, fit all-time low of the furthest flexible tap port to the proper supply pipeline by making a compression sign up with; then do the exact same for the various other faucet.
Turn on the supply of water and examine all joints and new pipework for leakages and also tighten them if essential. Fill the tub as well as also check the overflow electrical outlet as well as the normal electrical outlet for leaks.
Ultimately, deal with the bath paneling as described in the supplier's instruction manual. Tiling and also securing around the bath tub ought to wait till the bath tub has been used at the very least once as this will certainly settle it into its last setting.

 

 

Fitting New Touches

If the tails of the new faucets are plastic, after that you will certainly need a plastic port to prevent damages to the thread. One end of the port fits on the plastic tail of the faucet and the other end supplies a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly need lowering couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, position the faucet in the mounting hole in the bath/basin guaranteeing that the washers are in area in between the faucet and the sink. Secure the faucet in position with the manufacturer offered backnut. Once the faucet is safely in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap adapters. The former kind must be connected to the faucet ends first, tightening just by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been connected.

 

 

Tiling Around the Tub

In the location where the bathroom meets the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is essential as the installation can move enough to split an inflexible seal, creating the water to penetrate the wall between the bath and the tiling, resulting in issues with wetness and also possible leaks to the ceiling below.
You can choose from a selection of coloured sealers to blend in your components and also fittings. They are offered in tubes and also cartridges, and also are capable of sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with twists of drenched paper or soft rope. Bear in mind to always fill the bath tub with water before sealing, to allow for the motion experienced when the bathtub is in usage. The sealer can fracture fairly very early if you do not take into consideration this motion prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also quickly offered on the marketplace. It is suggested to fit the tiles utilizing waterproof or water-proof glue and cement.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

I was made aware of that article on How to Install a Bathtub Yourself from an associate on another domain. Sharing is nice. You just don't know, you could be helping someone out. Kudos for your time. Come back soon.

Diverse plumbing issues? We resolve.